To clean and dry your RV awning, remove loose dirt, wash both sides with a cleaner approved for the fabric, rinse thoroughly and leave it fully extended until the fabric, seams and edges are dry. Use gentle tools, avoid pressure washing and don't roll it up while it's damp unless you need to retract it temporarily for safety or travel.
How to choose an RV awning cleaner
Check your awning manual or identification label to find out which fabric you have. Most RV awnings use vinyl-coated fabric or woven acrylic, which need different care. Don't rely on appearance alone if you can't confidently identify the material.
You can usually wash ordinary dirt off vinyl's coated surface easily, but abrasive scrubbing can damage the coating. For woven acrylic, you need a cleaner that preserves its water-repellent treatment. Some awnings use other fabrics or finishes, so always follow the care instructions for your model.
Choose a cleaner approved for your fabric. You may be able to use a small amount of mild soap in water for routine washing if the manual permits it. Don't assume household detergent, dishwashing liquid or a general-purpose vehicle cleaner is suitable. Follow the dilution instructions and test the solution on an inconspicuous patch before cleaning the whole canopy.
How to prepare your RV awning for cleaning
Park on firm, level ground, secure your RV and extend the awning according to its operating instructions. Check for tears, loose stitching, damaged brackets or bent arms before you start. Stop if the fabric or mechanism looks unsafe to extend.
- Use a hose with a gentle spray, a clean bucket and a soft brush approved for the fabric.
- Keep a soft sponge or microfibre cloth ready for seams, edges and small marks.
- Move nearby items out of the way and close any openings that could let rinse water into your RV.
- Keep the spray away from electrical controls, sockets, lights and motor housings.
- Use an extension pole where practical rather than stretching from a ladder.
If you need a ladder, place it on a stable, level surface and maintain three points of contact while climbing, as advised by OSHA. Reposition it instead of leaning sideways. Never climb onto the awning or use its arms as handholds.
Make sure no one can operate a powered awning while you work. Disconnect its power only as the manual directs, and keep your hands away from hinges, spring-loaded arms and the roller mechanism.
How to clean an RV awning step by step
Work in small sections so the cleaner doesn't dry on the fabric. Clean the underside as carefully as the upper surface, since dirt and residue can transfer between them when you retract the awning.
- Gently brush away loose dust, leaves and grit. Don't drag gritty debris across the surface.
- Rinse both sides with a low-pressure spray to remove the remaining loose dirt.
- Apply the diluted cleaner with a sponge or soft brush, following the fabric manufacturer's instructions.
- Leave the cleaner on only for the recommended time. Keep the section damp without letting cleaner collect around fittings.
- Brush or wipe lightly, paying attention to edges, stitching and the valance. Gently support any loose fabric you can reach rather than pulling it tight.
- Rinse both sides thoroughly, working towards an edge so dirty water runs off instead of collecting.
Use gentle pressure only. You can damage coatings, loosen stitching or force water into places that should stay dry with a pressure washer, stiff brush or abrasive pad. Don't assume that standing farther away makes a pressure washer safe to use.
Continue rinsing until the runoff is clear and no suds remain. Don't roll the awning up to soak the fabric unless its care instructions recommend that method. Otherwise, you can trap cleaner against areas you haven't cleaned yet and struggle to rinse it out.
How to remove stains from an RV awning
Soften dried bird droppings with water and the approved cleaning solution before gently lifting them off. Avoid scraping with a blade or rubbing dry droppings into the fabric.
For sap or greasy marks, use only a spot treatment specifically approved for your awning material. You can damage coatings or leave permanent marks if you use acetone, petrol, strong solvents or undiluted degreasers. Test any approved treatment first, then rinse the treated patch thoroughly.
You may need a fabric-specific treatment rather than ordinary soap to remove mould or mildew. Don't use bleach without approval from the fabric manufacturer. If the manufacturer permits it, follow its instructions for dilution, contact time and rinsing. Never mix cleaning products.
Don't keep scrubbing simply because a dark mark remains. Repeated aggressive cleaning can damage the surface before you remove the stain. Ask an RV detailing professional or awning repair specialist to assess persistent marks, brittle patches or separating layers.
How to dry an RV awning completely
Leave your awning extended in its approved position, with space for air to circulate around both surfaces. If you can adjust its pitch, follow the manual to set an angle that lets rinse water drain off. Never move the arms or supports beyond their specified positions.
Use a clean, soft cloth to blot water from the valance, lower edge and fittings where you can reach them safely. Don't use a heat gun, hairdryer or direct heater to speed up drying. You can't rely on a fixed drying time because fabric construction, airflow and the amount of trapped water vary.
Check seams, hems and folds by touch before retracting the awning. These areas can remain damp after the main surface feels dry. Inspect the underside too, and wipe away any standing water you can safely reach around the roller without reaching into the mechanism.
How often should you clean your RV awning?
Inspect the canopy whenever you extend it. Remove bird droppings, sap and visible deposits promptly, and wash the whole awning when dirt builds up rather than following a rigid timetable. Check the care manual for any specified cleaning interval.
Before storage, make sure you've cleaned and thoroughly rinsed the fabric, then check that it's completely dry before rolling it up. If you must retract it while damp for safety or travel, extend it again at the earliest safe opportunity and let every layer dry.
After cleaning, look for frayed stitching, pinholes, coating damage and water collecting in a stretched section. Arrange repairs before further use if you find structural damage. Apply a fabric guard or water-repellent treatment only when the fabric manufacturer recommends it, using the specified product and method.