After detailing, check your RV for missed dirt, uneven finishes, damp upholstery, slippery surfaces and disturbed fittings. Your post-detailing inspection should also cover the agreed services, roof fittings, tyres and anything the detailer moved or cleaned around. Walk through the RV with the detailer before accepting the work, and ask them to remove residue, clean missed areas or investigate any damage you notice.
Check the services on your job sheet
Start with the written estimate or job sheet. A wash and wax doesn't necessarily include oxidation removal, roof cleaning, awning treatment, upholstery extraction or cleaning inside storage compartments, so judge the result against the services you authorised.
Ask the detailer to point out any stains, scratches or faded areas they couldn't safely improve. Compare these with your pre-service photographs, especially around decals, mirrors, compartment doors and other easily damaged parts. A permanent defect is different from an area the detailer simply missed.
Confirm which protective products the detailer applied and where. If you paid for paint correction or a coating, ask how they prepared the surface and request care instructions for the product. Water beading alone doesn't prove that they applied a particular coating.
Inspect the exterior finish and glass
View each side from several angles under good lighting. Look along the panels rather than only straight at them to spot streaks, patchy gloss, polishing marks and remaining chalky oxidation. On fibreglass, uneven gloss may indicate incomplete correction, although badly degraded gelcoat may need restoration beyond the service you booked.
Use this checklist without rubbing the finish with your bare hand:
- Check lower panels, wheel arches and the rear wall for road film or missed dirt.
- Inspect panel joints, badges and trim edges for dried polish or wax.
- Look for fresh scratches, circular polishing marks or cloudy patches on glossy surfaces.
- Check decals for lifted edges, abrasion or product trapped around the lettering.
- Inspect windows and mirrors from inside and outside for streaks, haze and residue along their edges.
Ask the detailer to remove any residue using a method suited to the material. Don't let anyone scrape dried product from paint, acrylic windows or decals with an unsuitable blade. Different RV window materials need different cleaners, so you can't treat every window like ordinary glass.
Check the roof, seals and awning
Inspect accessible roof edges, rooflights, vents and sealant joints for trapped dirt, leftover cleaner or signs that something has shifted. Look for lifted sealant edges, displaced vent covers and fittings that appear loose. Cleaning can reveal existing cracks, so compare anything suspicious with earlier photographs rather than assuming the detailer caused it.
Don't climb onto the roof just to inspect the result. Some RV roofs don't support foot traffic. Follow your vehicle manual and ask for photographs of areas you can't reach safely. A clean roof doesn't prove that the roof or its joints are watertight.
If your booking included awning cleaning, ask the detailer to extend it using the correct procedure. Inspect the fabric, seams, underside and roller area for remaining dirt or cleaner. Check that it's dry before the detailer rolls it away for storage. If it sticks, moves unusually or looks misaligned, have it checked rather than forcing the mechanism.
Check for slippery surfaces and blocked openings
Tyre sidewalls should look evenly finished, not wet with excess dressing. Check that no product has reached the tyre tread or brakes, and ask the detailer to arrange an assessment and remove any contamination safely before you move the RV. Inspect wheel faces, areas around the valves and wheel recesses for leftover cleaner.
If the service included tyre-pressure adjustment, confirm the readings against the vehicle manufacturer's specified cold pressures, not the maximum pressure moulded into the sidewall. The National Highway Traffic Safety Administration explains where to find recommended pressures and why you should check pressures when the tyres are cold.
Check entrance steps, grab handles, pedals and floor mats for slippery dressing. Look at appliance vents and drainage openings for cloth fibres, tape or cleaning residue. Confirm that exterior storage doors latch properly and that the detailer has replaced utility caps and covers.
Inspect the interior for dirt and dampness
Open the main entry door and check for persistent musty smells or a chemical smell strong enough to make you uncomfortable inside. Don't mistake fragrance for cleanliness. Ask which products the detailer used if an odour remains, and follow the products' ventilation instructions before occupying the RV.
Pay particular attention to hidden dampness after carpet or upholstery extraction. Press a clean, dry cloth against seat seams, carpet edges and accessible cushion undersides. Ask the detailer to allow more drying time if moisture transfers to the cloth, and don't close damp cushions inside storage bases.
Work through the areas included in your booking:
- Lift removable cushions and inspect seat bases, corners and accessible seat rails.
- Open cupboards and drawers to check for crumbs, cleaner residue and damp shelf liners.
- Inspect kitchen worktops, sinks and appliance seals for grease or sticky product.
- Check the toilet base, shower corners and washbasin fittings for missed deposits.
- Wipe a small area of flooring with a clean cloth to check for loose dirt or an oily film.
You may need to rinse food-contact surfaces after cleaning or sanitising, depending on the product label. Ask what the detailer applied rather than assuming that a dry surface is ready for food preparation.
Check fittings before accepting the work
Before leaving, check anything the detailer moved or disconnected. Confirm that seats lock into position, mats sit securely without obstructing pedals, cupboard catches engage and removable screens fit correctly. Where safe, test nearby lights, switches and powered fittings using their normal controls.
If you find moisture near electrical equipment, don't switch it on. Ask a qualified RV technician to inspect it. Detailing doesn't replace a mechanical inspection, and you can't judge an appliance's safety by its clean exterior.
Photograph unresolved defects and ask the detailer to record the agreed corrections on the job sheet. Collect the care instructions, including when you can wash treated surfaces or use cleaned upholstery. Arrange another inspection if you can't fully check the result at handover because materials are still drying or products are still curing.